ARCRON SYNCTIME PDF
ARCRON SYNCTIME UPGRADE

Click on вЂњUse the following IP AddressвЂќ Capture the IP address вЂ“ IP address will be the same as the Coms controller except the last digit must differ The Subnet mask and gateway IP must be the same as the coms controller Click on вЂњOKвЂќ SAM TrainingДЎ4 SAM2 вЂ“ Communication test via ECS2 Communication Controller вЂ“ вЂњRS485вЂќ Your Laptop IP address needs to be changed so that it is within range of the coms controller Connect LAN cable between the Coms controller and the Laptop Open Network settings Click on вЂњLocal area ConnectionвЂќ Click on вЂњPropertiesвЂќ Select вЂњInternet protocol Version 4(TCP/IP). Via the ECS(E1/Eth) communication controllerДЎ2 Laptop вЂ“ Set up SAM Training Laptop Set Up: SAM TrainingДЎ1 Testing Communication to the SAM or Access Control unit

ARCRON SYNCTIME UPGRADE

Open ECS(E1/ETH) ECT Insert вЂњUser nameвЂќ and вЂњPasswordвЂќ Select вЂњSerial Communication and click on вЂњLoginвЂќ 1 2 3 4 SAM TrainingД¤ ECS(E1/ETH) Set Up: Click on вЂњFindвЂќ to connect to unit Check that the units has the latest Firmware version being вЂњ вЂќ If Not on latest version, upgrade to latest version Click on вЂњDown LoadвЂќ Capture the IP address as indicated Click on вЂњSetвЂќ Click on вЂњSite InventoryвЂќ 2 1 3 1 SAM TrainingД®CS(E1/ETH) Set Up: Capture ECS(E1/ETH) Coms Port setup as per screen print Click on вЂњSetвЂќ on the вЂњNetworkвЂќ tab once done. Click on вЂњUpdateвЂќ Click on вЂњSet ConfigвЂќ 4 7 3 5 6 1 2 SAM TrainingДЎ RS232 Communication Test Cont Click on вЂњAlarm ConfigurationвЂќ tab Select вЂњRS485вЂќ under вЂњComs ConfigвЂќ Click on вЂњSetвЂќ Click on вЂњGet ConfigвЂќ Click on вЂњSet ConfigвЂќ Check that вЂњIntruderвЂќ alarm is number вЂњ9вЂќ Check that вЂњMovementвЂќ alarm is number вЂњ11вЂќ Close SAM2 ECT 4 5 3 2 SAM TrainingД§ ECS (e1/eth) communication Controller Set-UPД¬onnect a Straight RS232 cable the Lap Top and the ECS(E1/ETH) Coms Controller diagnostics port. Click on вЂњUpdate SAMвЂќ and wait until SAM has been updated вЂ“ This can be seen on the bottom left as indicated with the RED circle until it says вЂњreceivedвЂќ Click on вЂњSync TimeвЂќ Click on вЂњGet ConfigвЂќ and ensure that SAM2 shows you the current date and time.

RS232 Communication Test Cont Active communication will be shown on the bottom left as indicated with the RED circle until it says вЂњreceivedвЂќ Click on вЂњLoad ConfigвЂќ and select the applicable config file. Test communication to SAM1.5 or SAM2 unit via ECS (E1/Eth) coms Controller Test communication to Access Control unit via ECS (E1/Eth) coms Controller SAM TrainingД¬onnect a straight RS232 cable between the Lap Top and the SAM2 RS232 port(DB9 Connector on front panel Open SAM2 ECT Select вЂњCom PortвЂќ and double click on вЂњPasswordвЂќ SAM Training Set up ECS (E1/Eth) communication controller. INALA TECHNOLOGIEs Test Procedure: ECS (E1/Eth), SAM2, SAM1.5 & Access Version 1.0 We believe that learning not only New C_TS450_2020 Exam Duration occurs in the classroom but also through practical experiences.1 Test Procedure: ECS (E1/Eth), SAM2, SAM1.5 & Access

ARCRON SYNCTIME PDF

SAP C_TS450_2020 Exam Questions Pdf We have placed some demos for your reference, SAP C_TS450_2020 Exam Questions Pdf Free demo for your reference, SAP C_TS450_2020 Exam Questions Pdf And certification is the best proof of your wisdom in modern society, So now our SAP C_TS450_2020 study materials can help you do these and get certifications 100% for indeed, Using 's latest SAP certification C_TS450_2020 exam question bank, and it will brings you a lot of help.

Arcron synctime